UR-E8 to "T" Thread Adaptor (Part # NP0031)

Attach you CP5700 to microscopes and scopes using this "T" thread adaptor. You will still require the "T" male thread that corresponds with your scope.

Pictures of the adaptor attached to the 5700

No Longer Available

CP5700 - 46mm Thread Adaptor (Part # NP0019)

The 46 adaptor is great if what you are mainly trying to protect the lens of your CP5700. The adaptor has a o-ring which will snap into the lens cap holding groove on the front of the camera lens. It does come off but not easily enough for it to fall off and damage the lens. There is no vignetting using a single filter but if you use two filters or a Circular Polarizer there is a bit of vignetting at the widest lens setting. This adaptor can be used together with the Coolfix Variable adaptor as it fits through the inside diameter.

For use with filters only! Do not use with accessory lenses.

Pictures of the adaptor attached to the 5700

In Stock - $27

46mm Lens cap ( not tethered ) (Part # LC0046)

In Stock - $5

CP5700 - 52mm Thread Adaptor (Part # NP0021)

Use 52mm filters and protect the lens of your CP5700 by attaching this snap on 52mm thread adaptor. The adaptor has a o-ring which will snap into the lens cap holding groove on the front of the camera lens. It does come off but not easily enough for it to fall off and damage the lens. The 52mm thread adaptor can be used with one or more filters stacked together without causing vignetting. A 52mm lens cap will be needed. The adaptor can be left on the camera when turning it off.

For use with filters only! Do not use with accessory lenses.

Pictures of the adaptor attached to the 5700

In Stock - $27

52mm Tethered lens cap (Part # LC0052)

Out of Stock - $5

CP5700 - 58mm Thread Adaptor (Part # NP0033)

Use 58mm filters and protect the lens of your CP5700 by attaching this snap on 58mm thread adaptor. The adaptor has a o-ring which will snap into the lens cap holding groove on the front of the camera lens. It does come off but not easily enough for it to fall off and damage the lens. The 58mm thread adptor can be used with one or more filters stacked together without causing vignetting. The outside diameter is equal to the outer diameter of the camera lens body. A 58mm lens cap will be needed. The adaptor can be left on the camera when turning it off.

For use with filters only! Do not use with accessory lenses.

In Stock - $27

58mm Tethered lens cap (Part # LC0058)

In Stock - $5

Coolfix Variable Adaptor 5700 (Part # NP0104)

This is a variable length thread adaptor that can be used in place of the UR-E8 Nikon adaptor. The set consists of an aluminum inner barrel and an aluminum outer barrel with a 62mm thread. The inner barrel has the same threads as the UR-E8 and can be used to mount the Nikon accessory lens. With a 62mm filter attached and the outer barrel pulled back to the camera lens there is no vignetting. The 46mm snap on adaptor will fit inside of the main barrel allowing you to use the variable adaptor as a lens hood. This combination can be left on the camera. The adaptor will block some light from the internal flash when shooting at full wide angle. I recommend setting the zoom speed to slow when using the variable adaptor with filters.

No Longer Available

62mm Tethered lens cap (Part # LC0062)

In Stock - $5

Step Down Ring 62mm to 55mm (Part # NP0024)

This is a 62mm to 55mm step down ring for the Coolfix variable length 5700. This can be used to mount the Olympus TCON17 or B300 (1.7x lenses) to the variable adaptor. If used with 55mm filters there will be vignetting in the wide range of the camera lens.

In Stock - $15

UR-E8 Back cap (Part # NP0028)

Do you want to leave the UR-E8 attached to the accessory lens? Use this back cap to close off the UR-E8 and keep out the dust.

In Stock - $27

UR-E8 to ES-E28 Slide copy adaptor (Part # NP0029)
This is the adaptor only. Does not include the slide copying attachment.

If you want to copy slides using your Nikon ES-E28 Slide copying attachment on your CP5700 then you will need this adaptor. This is not the complete slide copier! This adaptor replaces the rear 28mm threaded section of the slide copy unit with a 50mm threaded section that screws into the Coolfix Variable adaptor or the UR-E8. Comes black anodized and includes an allen key to do the simple conversion.

In Stock - $35